TO ORDER THIS UNIT, PLEASE ADD TO CART AND CHOOSE LOCAL PICK-UP.  WE WILL SHIP USING ESTES EXPRESS.  WE SHIP TO ADDRESSES IN THE USA. 

STILL ON BACK-ORDER

SKID MOUNTED COLD 10 GPM 3000 PSI PRESSURE WASHER W/ GREEN SPRING YU21405S UNLOADER HONDA MUFFLER 

MUST TIGHTEN BELTS AFTER 30 DAYS.  NO WARRANTY ON BELTS.  UNLOADER SETTINGS, CLOGGED NOZZLES AND LOOSE BELTS ARE SOME CAUSES OF BELT FAILURE.  MUST USE THE 50' OF 1/2" ID HOSE WITH THIS UNIT 

This powerful, time saving skid unit will arrive with a 1" hose barb on the inlet of the pump.  We STRONGLY recommend that you purchase our PL-8-TA kit for a tote or a horizontal leg tank or a PL-8-TO for an IBC tote which has everything you need to correctly plumb this unit.  We recommend switching out the factory installed 1" barb to our 1.5" hose barb, upsizing the non-collapsible suction hose to 1.5" ID, upsizing the filter to 80 mesh 1.5" Y-Strainer, installing a 1.5" bulkhead, brass hose barb and 1/2" bulkhead.  Increase the jump hose to the reel to a 1/2" high pressure hose and use a 50' hose as the first length of hose on the reel.  (Always strip all hose from the reel except the last single wrap to protect the crimp when in use.)  Upsizing the hose ID's will allow you to shoot farther, increase the cleaning units and efficiency of your pressure washer as well as move much faster when using your surface cleaner.  The PL-8-TA OR PL-8-TO kit has everything you need to plumb the pressure washer as well as connect to a reel including the 50' high pressure hose.  

Up-Sizing your hoses will prevent back-pressure to your pump, help your valves and high pressure seals last longer, prevent your safety relief valve from spraying water, help your pump run at a cooler temperature, supply enough water to your pump using the 'double your supply hose ID in relation to your inlet port' rule and keep your pump cooler leading to less down time.  Double check your surface cleaner hose to ensure that it is 3/8" ID instead of 1/4".  

Always use Medium Threadlock on your high pressure fittings instead of Teflon Tape.  Teflon Tape will end up in the pump valves or clog nozzles.

YOU NEED TO BUY A BATTERY AND BATTERY BOX AND ADD A REMOTE FUEL TANK.  ADD FUEL AND CONNECT TO A MINIMUM OF 200 GALLON WATER TANK OR IBC TOTE.

ADD A HIGH TEMPERATURE HUDSON FLOAT VALVE (HUDSON-HT) AND HUDSON FLOAT VALVE INSTALLATION KIT (HUDSON-A) TO PREVENT OVER-FILLING YOUR WATER TANK.  THE HUDSON FLOAT VALVE WILL AUTOMATICALLY STOP THE FLOW INTO YOUR TANK WHEN INSTALLED PROPERLY IN THE HEADSPACE OF YOUR WATER SUPPLY TANK.

CHECK OUT OUR PLUMBING DIAGRAM AT THE LINK BELOW:

https://www.pressurewasherproducts.com/pressure-washer-plumbing.html

STANDARD FEATURES

• YU21405S unloader 
• TSF2221 belt driven pump
• Engine and pump oil drains offer easy maintenance
• 3VX banded belt system offers balanced power transfer
• iGX800 Honda:  Electronic fuel injection provides higher output and performance
• Lower vibration and quieter operation
• All units feature electric start and include marine battery box

 NOTE: All units are completely factory assembled, tested in the USA, and delivered ready to operate.  Bypass hose will arrive with a small amount of water in hose from testing at the factory.

WE HIGHLY RECOMMEND ADDING THE BEST HIGH PRESSURE 3/8" BALL VALVE (6292) TO THIS ORDER TO ALLOW YOU TO TURN OFF THE FLOW OF WATER TO SWITCH FROM THE GUN TO A WHISPER WASH CLASSIC SURFACE CLEANER (4345).  YOU WILL NEED TO ASK FOR TWO NOZZLES 6.0 25 DEGREES FOR A TWO NOZZLE SPRAY BAR (PART 1848 OR 1118)  OR FOUR NOZZLES 3.0 25 DEGREES FOR A FOUR NOZZLES SPRAY BAR (PART 1769).

MOUNTING HOLES:  11 1/8"  X 24"

THE 19" WHISPER WASH CLASSIC, THE 24" GROUND FORCE, 24" LIL BIG GUY OR THE 28" BIG GUY WITH THE UPGRADED 3/8" HIGH PRESSURE HOSE IS THE PERFECT COMPLEMENT TO THIS COLD PRESSURE WASHER.  KEEP IN MIND THAT THE WIDER THE SURFACE CLEANER, THE SLOWER YOU WILL MOVE.  YOU CAN CHOOSE ANY SURFACE CLEANER THAT YOUR HEART DESIRES AND JUST ABOUT ANYONE WILL SELL IT TO YOU BUT UNDERSTAND THAT THE 19-24" SURFACE CLEANERS ARE THE BEST MATCH FOR THE 8 GPM PRESSURE WASHERS.  WHISPER WASH WILL CUSTOMIZE THE HANDLES, THE SPRAY BAR AND WHEEL SET-UP TO MEET YOUR NEEDS. FOR EXAMPLE, IF YOU WANT THE CLASSIC HANDLE ON THE GROUND FORCE WITH A 4 TIP BAR, THEY WILL ASSEMBLE THAT CUSTOM SURFACE CLEANER FOR YOU.

AS WITH ANY PRESSURE WASHER, DO NOT ADJUST THE UNLOADER.  THE UNLOADER IS SET AT A SPIKE PRESSURE OF 200 PSI ABOVE THE OPERATING PRESSURE OF THE PUMP AND MEANT TO BE LEFT ALONE.  IF YOU NEED LESS PRESSURE, CHANGE OUT THE NOZZLES TO A LARGER ORIFICE AND NEVER SMALLER THAN WHAT IS CALLED FOR USING FACTORY SPECIFICATIONS USING GPM AND PRESSURE.  THIS UNIT REQUIRES A 8.5 ORIFICE OR LARGER NOZZLE.  YOU CAN ADD A 6540-8 JROD KIT & THE KYLE DAVIS LONG RANGE SHOOTER NOZZLE (SN8) TO THIS PRESSURE WASHER TO EXPERIMENT WITH PRESSURE AND DISTANCE.