8 gpm 3000 psi Skid Cold Pressure Washer Honda General Pump TSF2021 S/VB8030HGEA406
Skid Mounted Cold 8 GPM 3000 PSI Pressure Washer
Pressure Pro S/VB8030HGEA406
18" width x 32" long approximately
8 GPM 3000 psi Honda GX630 General Pump V-Belt special powder coated steel frame, commercial lock up, pressure trapped unloader, gun/wand assembly with quick connects, 50' grey high-pressure hose with quick connects, 5 quick connect colored nozzles, 20% high draw chemical injector assembly with quick connects
Standard features:
- Lifetime frame warranty
- Easy access single bolt interlocking belt cover
- Single bolt engine adjustable belt tension
- EZ-start valve.
- Adjustable pressure unloader but is set at 3200 psi and meant to be left alone and never adjusted.
- Engine and pump oil drains offer easy maintenance.
- Dual padded shock absorbing feet
- 3XV425 belt system offers balanced power transfer.
- Commercial/industrial grade engines
- Low speed pump and thermo-sensor (prevents overheating in bypass mode)
- Remote six-gallon poly fuel tank-non-carb evaporative compliant-not for sale to California-see options for California compliant upgrade
- Marine battery box
Note: All units are completely factory assembled, tested in the USA, and delivered ready to operate.
We highly recommend adding the best high pressure 3/8" ball valve (6292) to this order to allow you to turn off the high-pressure flow of water to switch from the gun to a Whisper Wash classic surface cleaner (4345).
The 19" Whisper Wash Classic or the 24" Ground Force are the perfect complement to this cold pressure washer. Keep in mind that the wider the surface cleaner, the slower you will move. You can choose any surface cleaner that your heart desires and just about anyone will sell it to you but understand that the 19 - 24" surface cleaners are the best match for the 8 GPM pressure washers.
This pressure washer must be tank fed with a minimum 1.5" non-collapsible suction hose (AGC24), 1.5" 80 mesh Y-strainer (YS24H), the special 3/4" to 1.5" hose barb for the pump inlet (5049), 1.5" hose barbs (HB2424P), stainless steel hose clamps and the 1.5" bulkhead (BH24) or assembly for a tote outlet (CL32). We carry everything you need to plumb this pressure washer in a kit which is part number, PL-8-TA for a horizontal leg tank or PL-8-TO for an IBC tote.
You can order this pressure washer with a K7.3 unloader.
As with any pressure washer, do not adjust the unloader. The unloader is set at a spike pressure of 200 psi above the operating pressure of the pump and meant to be left alone. If you need less pressure, change out the nozzles to a larger orifice and never smaller than what is called for using factory specifications using GPM and pressure. This unit requires an 8.5 orifice or larger.
You need two 4.5 25-degree nozzles for a two nozzle spray bar (1845) or four 2.5 25-degree nozzles for a four-nozzle bar (1955).
If you find that you are plagued by the need to change out leaking O-Rings, repair blown hose ends, replace quick connects and deal with the effects of a pressure trapped unloader, consider upgrading to a flow sensitive unloader. Using a flow sensitive unloader such as the K7.3 will result in O-Rings lasting longer, plugs not receiving the 'ping marks', no more fights with the hose and less blown hose ends.
Always install your chemical injector at least 2-3 feet downstream from your unloader to prevent back-siphoning of chemicals into the 'guts' of your unloader. Always remove your chemical injector when not in use. Look at the orifice inside the chemical injector and notice the restriction it causes in flow and pressure. When using your surface cleaner, you need as much flow and pressure as possible.
Install a Hudson float valve (Hudson-HT) using everything you need to install it with our Hudson assembly (Hudson-A or HB). The Hudson Assembly installs into the very top of the water tank using a bulkhead and garden hose connection to prevent the tank from over-flowing.
SKU: PW.S/VB8030HGEA406
