1.5" ID x 100' Roll Non-Collapsible Supply and Suction Hose
1.5" ID Non-collapsible supply / suction hose for pumps and for the Suttner sludge pump outlet. You can't have enough of this hose.
This is the Spiralite 115 grade hose. The wall is a little thicker than some of the other manufacturers out there that we have seen.
Hose will be sent in one continuous length unless you send a note indicating otherwise.
________________________________________________________________________
We carry this hose in:
3/4" ID Non- Collapsible Supply/ Suction Hose (per foot)
1" ID Non- Collapsible Supply/ Suction Hose (per foot)
1.5" ID Non- Collapsible Supply/ Suction Hose (per foot)
2" ID Non- Collapsible Supply/ Suction Hose (per foot)
We also offer this hose in a wire reinforced hose in the same hose ID's.
This 1.5" supply hose can be used with corrosive chemicals such as sodium hypochlorite and sodium hydroxide.
***Supply / Suction hose inner diameter (ID)should be doubled compared to the pump inlet/suction port. For example, the TS2021 (HP5535) has a 1/2" inlet on either side of bottom manifold of the pump. The pump should be supplied with 1" non-collapsible suction hose.
________________________________________________________________________
Minimize the use of extra fittings
Do NOT use galvanized fittings or metal ball valves between your pump and water tank because they will likely corrode and flake little chunks into your pump valves leading to vibration and/or damage. Avoid extra elbows. Do not use PVC pipe anywhere. PVC pipe can become brittle and doesn't tolerate the weight of a surface cleaner, ladder, or your body weight for long.
If not installed correctly, air will find its way into your pump leading to manifold damage. Install components using non-drying liquid Teflon and never use Teflon tape.
Never adjust your unloader
The unloader should be set using a whip hose, high pressure ball valve, high pressure steel tee, snubber, and gauge to 200 psi above the operating pressure of the pump and left alone. Do NOT install check valves or any type of swivel fitting on the suction/supply hose assembly or air may become entrained causing extensive damage from cavitation.
How to install the hose onto the hose barb
When installing the hose into hose barbs, first slide the hose clamp a few feet away from the cut end. Grab some Slo-Mo soft wash surfactant for sodium hypochlorite, dish soap or shampoo and coat your finger or old toothbrush with a generous amount. Apply the soap to the inside several inches and to the barb end of the hose barb. Turn on the heat gun and hold the heat source about 3-4" away from the hose end while rotating the hose as you try to apply the heat as evenly as possible. Heat only until the hose turns shiny and releases a single plume of smoke. Turn off the heat gun and set it aside to cool. Install the barb into the hose end and push it down against the ground or vertical surface. Allow the end to cool naturally, move the hose clamp up about 1/16" or 1/8" from the end toward the thread and tighten securely.
Install the hose clamp to allow you to access it easily in the future so that you do not have to struggle to use a tool on the clamp.
The unloader bypass hose that sends water back to the tank when you release the trigger on your gun should be installed using 3/8" or 1/2" kink resistant hose. The port should be installed so that the stream of water shooting into the tank does not point directly at the pressure washer suction/supply bulkhead. You don't want to create air bubbles in your supply water. The bypass hose running back to your tank will act as a back-up for your thermal relief valve mounted on the opposite side of your pump to the suction hose.
Do not use Teflon tape on any fittings
Use medium, removable threadlock (5003, 10 ml or 5004 50ml). Try not to use elbows or extra fittings. When at all possible, minimize the use of quick connects. Install the chemical injector at least 3' away from the unloader to prevent back-siphoning of chemical into the internal components of the unloader. Always remove the chemical injector assembly when not in use.
SKU: AGC24-100
Questions: websales@pressurewasherproducts.com or call (727) 562-5488
