Skip to content
SKU AGB16

1" ID TigerFlex Blue Water Non-Collapsible Suction Tank Feed Hose Sold Per Foot

Original price $2.60 - Original price $2.60
Original price
$2.60
$2.60 - $2.60
Current price $2.60

       TigerFlex Blue Water 1" ID Non-collapsible and PVC reinforced supply / suction hose for low- and high-pressure pumps sold per continuous foot (12").

  • 1.26 Inch OD
  • 90 PSI Working Pressure at 68 degrees F
  • 65 PSI Working Pressure at 104 degrees F
  • 3" Bend Radius at 68 degrees F

 

Hose is available in 100' continuous run or longer by special order.

 

DO NOT USE this hose on the discharge side of pumps.

 

Inlet line size should be adequate to avoid starving the pump.

  • Line size must be a minimum of one size larger than the pump inlet fitting. 
  • Avoid tees, 90-degree elbows or valves in the inlet line of the pump to reduce the risk of flow restriction and cavitation.
  • The line must be a flexible hose, not a rigid pipe, and reinforced on suction systems to avoid collapsing.
  • The simpler the inlet plumbing the less the potential for problems. keep the length to a minimum, the number of elbows and joints to a minimum (Ideally no elbows) and the inlet accessories to a minimum.
  • Use pipe sealant to assure air-tight, positive sealing pipe joints.

       All-Flo states that the suction hose should be up to 3 x the inner diameter compared to the inlet port of the pump.

       Hose will be slightly generously cut and sent in one continuous length unless you send a note indicating otherwise.  

       This hose is great for high pressure pumps with a 1/2" inlet, 1/2" air diaphragm pumps, 12-volt pumps with a 1/2" suction or supply port and can be used with corrosive chemicals such as sodium hypochlorite and sodium hydroxide.  

***Supply/suction hose inner diameter (ID) should be doubled compared to the pump inlet/suction port.  For example, the General Pump TS2021 (HP5535) has a 1/2" inlet on either side of the bottom manifold of the pump. The pump should be supplied with 1" non-collapsible suction hose.

       Mount the pressure washer as low to the surface as possible in relation to the supply port/bulkhead of the water tank but remember to use shock absorbing rubber pucks (Part# 4542) on your skid L-brackets (1213) of the pressure washer. Most pressure washers can be converted from cart with wheels to skid units by removing the wheels and installing L-brackets for your unit available through us.

       Minimize the use of extra fittings. Do not use galvanized fittings or metal ball valves between your pump and water tank because they will likely corrode and flake little chunks into your pump valves leading to vibration and/or damage. Avoid extra elbows. Do not use PVC pipe anywhere. PVC pipe can become brittle and doesn't tolerate the weight of a surface cleaner, ladder, or your body weight for long. If not installed correctly, air will find its way into your pump leading to manifold damage. Install components using non-drying liquid Teflon and never use Teflon tape.

       Never adjust your unloader- The unloader should be set using a whip hose, high pressure ball valve, high pressure steel tee, snubber, and gauge to 200 psi above the operating pressure of the pump and left alone. Do not install check valves or any type of swivel fitting on the suction/supply hose assembly or air may become entrained causing extensive damage from cavitation. 

       Working with non-collapsible hose can be challenging. When installing the hose into hose barbs, first slide the hose clamp a few feet away from the cut end. Grab some Slo-Mo Softwash surfactant for sodium hypochlorite, dish soap or shampoo and coat your finger or old toothbrush with a generous amount. Apply the soap to the inside several inches and to the barb end of the hose barb. 

       Turn on the heat gun and hold the heat source about 3 - 4" away from the hose end while rotating the hose as you try to apply the heat as evenly as possible. Heat only until the hose turns shiny and releases a single plume of smoke. Turn off the heat gun and set it aside to cool. Install the barb into the hose end and push it down against the ground or vertical surface.  allow the end to cool naturally, move the hose clamp up about 1/16" or 1/8" from the end toward the thread and tighten securely. Install the hose clamp to allow you to access it easily in the future so that you do not have to struggle to use a tool on the clamp.

       The unloader bypass hose that sends water back to the tank when you release the trigger on your gun should be installed using 3/8" or 1/2" kink resistant hose. The port should be installed so that the stream of water shooting into the tank does not point directly at the pressure washer suction/supply bulkhead. You don't want to create air bubbles in your supply water. The bypass hose running back to your tank will act as a back-up for your thermal relief valve mounted on the opposite side of your pump to the suction hose assembly.

       Do not use Teflon tape on any fittings. Use medium, removable thread lock (5003, 10 ml or 5004 50ml). Try not to use elbows or extra fittings. When at all possible, minimize the use of quick connects. Install the chemical injector at least 3' away from the unloader to prevent back-siphoning of chemical into the internal components of the unloader. Always remove the chemical injector assembly when not in use.  

Use a R2 or 2 wire jump hose on the high-pressure outlet of your unloader to your reel.

Condition: New

 

SKU: AGB16

 

Secure Checkout Badge
Dedicated Support

We offer chat support during store hours

Call Us Anytime

+1 (727) 562-5488

Wide Product Selection

Find The Right Tool For Every Job

Fast and Reliable Shipping

Timely Delivery to Your Doorstep

Testimonials

I recently purchased a pressure washer from Pressure Washer Products, and the experience was fantastic from start to finish! The staff is incredibly knowledgeable and helped me find the perfect model for my needs. They answered all my questions and even gave me tips on maintenance and usage. The quality of their products is top-notch.. Highly recommended!

Kerolos Mamdoh

The best pressure washing store hands down. Rex the owner and his team have a wealth of knowledge about the industry. Lori is always there to help you with what you need. I’ve saved alot of money over the years through them because they help to educate you on what products and equipment are best to buy for your specific set up/washing goals. Other places attempt to drain your bank account if you let them. Not here, that’s why they have customers for life

Jared Policandriotes

I recently bought a surface cleaner from PWP, and it's been a game-changer. Lori helped me find the right tips for my machine, and the results have been fantastic. Thanks, Lori!

Sheriff Khalifa

Lori was very helpful and got us out surface cleaner and recommended what tips to match our machine. Runs fantastic. She also recommended a chemical injector to try on our trailer and it has been another great upgrade. Lori knows her stuff and the price and shipping was reasonable!

Brent Batton

I am a new customer to this business and have been here three times. Each time I have received fantastic customer service. I am glad there is actually a local business around that deals specifically with pressure washers. Highly recommended.

Doug Williams

I love this store. Laurie and Rex/ Family have been a huge help in understanding aspects of the equipment and tools we use in this industry. I’ve learned lots from them. Also the pricing and amount of supplies the store has to offer is perfect for a quick trip to load up and head out.

JR Pressure Wash Service

Search

Use this section to help customers find the products they're looking for.