8012Pro Hot Super Skid 8 gpm 3500 psi K7.3 Unloader 12 Volt Pro-Super Skid
8012Pro Hot Super Skid 8 gpm 3500 psi K7.3 Unloader 12 Volt Pro-Super Skid
We strongly recommend that you inspect your belts after 30 days for adjustment. No warranty on belts. Unloader settings, clogged nozzles and loose belts are some causes of belt failure.
This powerful, time saving hot skid unit will arrive with a 1" hose barb on the inlet of the pump. We strongly recommend that you purchase our PL-8-TO or PL-8-TA kit which has everything you need to correctly plumb this unit. We recommend switching out the 1" barb to 1.5", upsizing the non-collapsible suction hose to 1.5" ID, upsizing the filter to 80 mesh 1.5", installing a 1.5" bulkhead, brass hose barb and 1/2" bulkhead. Increase the jump hose to the reel to a 1/2" high pressure hose and use a 50' hose as the first length of hose on the reel. (Always strip all hose from the reel when in use.) Upsizing the hose ID's will allow you to shoot farther, increase the cleaning units and efficiency on your pressure washer as well as move much faster when using your surface cleaner.
Upsizing your hoses will prevent back-pressure to your pump, help your valves and high-pressure seals last longer, prevent your safety relief valve from spraying, supply enough water to your pump using the 'Double your supply hose ID in relation to your inlet port' rule and keep your pump cooler leading to less down time. Always use medium Threadlock on your high pressure fittings instead of Teflon tape. Teflon tape will end up in the pump valves or clog nozzles.
If using a chemical injector, install the injector only when in use and install it several feet downstream of the unloader to prevent back-siphoning into the unloader/pump manifold.
Rugged powder-coated steel, low-profile frame w/ forklift channels
48L x 43W x 48H frame dimensions offer versatile installation
Super efficient schedule 80 coil
Stainless steel coil wrap, burner hood, and control panel
On board 15-gallon poly fuel tank-non-carb evaporative compliant
Reliable Honda gasoline commercial/industrial electric start engines
Yes, this unit is key start and not pull cord start
Fully self-contained, no external power required.
Belt driven TSF2021 General Pump
Reliable Beckett burner
Adjustable thermostat
3VX425 belt system offers balanced power transfer
Engine and pump oil drains offer easy maintenance
Safety pressure relief valve
120-degree temp rise available
Approximately 650 lbs
Add fuel and connect to a minimum of 200 gallons water tank or IBC tote.
Standard accessories included below:
Gun/wand assembly with insulated grip and quick connects.
50' high pressure hose w/quick connects.
Maxi-Flo 20% chemical injector assembly w/quick connects
4 color-coded QC spray nozzles
1 color-coded QC chemical nozzle
Note: 12v units include 20 amp charging system
Must use a 9.0 turbo nozzle on this unit or part 4656.
Regarding K7 or flow actuated unloaders: The normal operating RPM on most Honda engines is between 2000-3900. If you run them lower than 2000 for extended periods of time, the combustion chamber will carbon up with unburned fuel and foul the spark plugs (per Honda). The K7 needs full throttle.
Note: All units are completely factory assembled, tested in the USA, and delivered ready to operate. Must provide a battery.
Wonder what the difference is between a Hot Box and a Super Skid? We asked Bill Matthews from Pressure Pro. His response is copied below:
As for the burner efficiency, they would be within only a few percent of each other typically in the upper 70-80 percent range (Roughly 76-82%).
The best comparison you made would be that the fuel capacity is diminished for the hot box by 31% and for the gas engine by 50%.
One advantage would be that the HBS12V80 has a slightly larger coil and would allow for a slightly larger heat rise roughly 10° but would consume roughly .7 gph more fuel.
8012PRO-35HG 2.8 gph diesel (approx 170°) (12-gallon tank approx 4.28 hrs)
Honda GX690 1.8 gph gas (12-gallon tank approx 6.66 hrs)
*************************************************
HBS12V80 3.5 gph diesel (approx 180°) (8.5-gallon tank approx 3.03 hrs)
Honda GX690 1.8 gph gas (6-gallon tank approx 3.33 hrs)
Both motor pump configurations are virtually identical.
We recommend the Whisper Wash 19" Classic, 24" Ground Force (6715), 24" Lil' Big Guy or the 28" Big Guy for use with this 8 gpm hot skid. Using a larger diameter surface cleaner will cause the user to move more slowly than if using the 19"-24" unit.
We strongly recommend that you add a 6540-8 JROD kit & the Kyle Davis long range shooter nozzle (SN8I).
SKU: PW.835K7
